.

Talk about music gear for noise music

Moderator: xome

Post Reply
User avatar
MKULTRA
Posts: 2777
Joined: Sat Sep 13, 2008 6:04 am

.

Post by MKULTRA » Thu Mar 29, 2018 3:55 am

.
Last edited by MKULTRA on Sun Aug 26, 2018 4:51 am, edited 2 times in total.

User avatar
xdugef
Posts: 13320
Joined: Tue Jun 14, 2005 11:26 am
Location: 噪声æº￾
Contact:

Re: Reliable Soldered Connections

Post by xdugef » Thu Mar 29, 2018 9:12 am

You to tell me twisting the wires and holding it in place with hot glue is not sufficient??

User avatar
fire
Posts: 2470
Joined: Tue Aug 17, 2010 2:15 pm
Location: noritual unformation

Re: Reliable Soldered Connections

Post by fire » Thu Mar 29, 2018 3:43 pm

rich people and their fancy solder and hot glue :roll:

TWISTED 4 LYFE
broadcasting from the post-internet wasteland

User avatar
jliat
Posts: 2692
Joined: Tue Nov 20, 2012 1:34 am
Contact:

Re: Reliable Soldered Connections

Post by jliat » Sun Apr 01, 2018 8:35 am

So guys where am I going wrong?


Image

User avatar
crochambeau
Posts: 2814
Joined: Sat Nov 19, 2005 12:48 pm
Location: earth.
Contact:

Re: Reliable Soldered Connections

Post by crochambeau » Sun Apr 01, 2018 6:10 pm

jliat wrote:
Sun Apr 01, 2018 8:35 am
So guys where am I going wrong?


Image
We'd have to see your technique to answer that question. I wouldn't want to use that for SMD (or at all, if I'm being honest) but people have done great things with worse.

User avatar
MKULTRA
Posts: 2777
Joined: Sat Sep 13, 2008 6:04 am

Re: Reliable Soldered Connections

Post by MKULTRA » Tue Apr 03, 2018 9:57 am

.
Last edited by MKULTRA on Fri Aug 24, 2018 1:49 am, edited 1 time in total.

User avatar
xdugef
Posts: 13320
Joined: Tue Jun 14, 2005 11:26 am
Location: 噪声æº￾
Contact:

Re: Reliable Soldered Connections

Post by xdugef » Tue Apr 03, 2018 10:49 am

We had a soldering project in shop class.. we had to make these coin tray with a handle and each corner connection had a different type of solder, braise, spot weld or rivet.. I forget all the methods used.. I think there were two others.. I still have the thing. Anyway I did all the joints correctly but had made the tray a half inch narrower than specified and one of my redneck classmates tried to rat me out to the teacher after he approved by welds and shit and his response to them was "well at least he made the joints correctly". :lol:

User avatar
fire
Posts: 2470
Joined: Tue Aug 17, 2010 2:15 pm
Location: noritual unformation

Re: Reliable Soldered Connections

Post by fire » Tue Apr 03, 2018 11:06 am

MKULTRA wrote:
Tue Apr 03, 2018 9:57 am
" You keep making mistakes because you are focusing on the solder joint and not what you are doing."
perfection requires no attention to detail for at that moment of focus you err
broadcasting from the post-internet wasteland

Post Reply

Who is online

Users browsing this forum: No registered users and 12 guests